CRUX : Home

Home :: Documentation :: Download :: Development :: Community :: Wiki :: Ports :: Bugs :: Links :: About

Installing CRUX

Supported Hardware / Requirements

Packages on the official CRUX ISO image are compiled with optimization for x86-64 (AMD Athlon 64, Intel Core, Intel Atom) or newer processors. Do not try to install it on an i686 (Pentium-Pro, Celeron, Pentium-III) or lower processor, since it simply will not work.

A minimum of 192MB system memory is required to install CRUX from CD-ROM or removable flash drive. It is possible to perform a custom chroot installation with only 16MB of RAM.

The kernel used during installation, i.e. when booting from the CRUX ISO image (El Torito), is compiled with the following disk controllers and USB support:.

SubsystemDriver(s) included in bootkernel
PATA/IDEALi, AMD/Nvidia, ARTOP 6210/6260, ATI, CMD64x, CS5510/30/35/36, Cypress CY82C693, EFAR SLC90E66, HPT 34x/36x/37x, ITE 8211/12/13, JMicron, Marvell, NETCELL Revolution, Ninja32/Delkin, Nat Semi NS8741x, Intel PIIX/SCH/MPIIX, OPTI FireStar/621x, Promise, RADISYS 82600, SC1200, SERVERWORKS OSB4/CSB5/CSB6/HT1000, CMD / Silicon Image 680, SiS, Compaq Triflex, VIA, Winbond SL82C105, ISA Plug & Play, PC Tech RZ1000, Generic
SATAAHCI, Intel ESB/ICH/PIIX, Initio 162x, Silicon Image/Silicon Image 31xx, Pacific Digital ADMA/QStor, Promise SX4/TX2/TX4, Marvell, Nvidia, SiS 180/96x, Broadcom/ServerWorks/Apple K2, ULi, VIA, Vitesse VSC7174/Intel 31244
SCSI/SAS3Ware 5/6/7/8/9xxx, HP Smart Array, 7000FASST, ACARD, Adaptec AHA15xx/28xx, Adaptec AACRAID, Adaptec AIC7xxx/79xx/94xx, Adaptec I20, Marvell 88SE64xx/94xx, Advansys, Always IN2000, ARECA 11xx/12xx/13xx/16xx, LSI Logic New/Legacy/MegaRAID/MPT, HighPoint RocketRAID 3xxx/4xxx, BusLogic, VMware PVSCSI, DMX3191D, DTC 3x80, EATA, Future Domain 16xx/Adaptec AHA2920A, Intel/ICP, IBM ServeRAID/Power Linux, Initio 9100U/INI-A100U2W, NCR53c406a, Promise SuperTrak EX, SYM53C8xx, PAS16, Qlogic FAS, Qlogic QLA 1xxxx/2xxx, Qlogic ISP 4xxx/82xx, Emulex LightPulse FC, Symbios 53c416, Tekram DCxxx, Trantor Txxx, UltraStor, UltraStor 14F/34F
USBEHCI HCD (USB 2.0) support, UHCI (Intel PIIX4, VIA, ...) support, OHCI (Compaq, iMacs, OPTi, SiS, ALi, ...) support, USB Mass Storage support, USB Human Interface Device (full HID) support, HID input layer support

In order to install CRUX, your disk controller must be present in the list above. If your hardware is not supported or you have other problems installing CRUX, you might find a solution in the CRUX wiki.

Installing From CD-ROM or removable flash drive

 $ md5sum crux-3.3.iso

Compare the output with the file crux-3.3.md5, which can be found in the same directory as the ISO image on the download site. If the checksums match, the download was successful and you can continue by burning the ISO image to a CD or writing it to a removable flash drive.

 $ fdisk /dev/sd?
 $ mkfs.???? /dev/sd??
 $ mkswap /dev/sd??

Note

Please keep in mind that SATA harddisks are usually detected as SCSI devices. The first SATA disk is called /dev/sda instead of /dev/hda. For more information about harddisk naming conventions please refer to the Linux Partition HOWTO.

The amount of disk space required depends on how many packages are selected to install. It is recommended to have at least a 1G root partition (CRUX will use about 200MB-500MB, depending on your configuration).

Note: UEFI

For UEFI installation a GPT disklabel and an EFI system partition (ESP) are required in most cases. The ESP does not need to be very large (100MiB for example) and should be formatted with a FAT32 filesystem and flagged as bootable. When using UEFI the boot loader/manager will be installed in the ESP rather than the traditional method of installation into the Master Boot Record (MBR).

CRUX supports all the filesystems supported as root filesystems by the linux kernel: btrfs, ext2, ext3, ext4, JFS, reiserfs and XFS. Further, it is highly recommended to separate the system data from user data, i.e. use a separate partition for /home (and possibly /var) since that will make your life a lot easier the day you want to upgrade/reinstall/remove your system.

Note

Make sure the appropriate userspace filesystem-tools are installed. xfsprogs, btrfs-progs, jfsutils and reiserfsprogs can be found in the opt repository.

Note

Make sure that any BIOS Virus Protection option is DISABLED as this option may prevent fdisk from writing new partitions correctly.
 $ mount /dev/sd?? /mnt

If you want the installation to span more than one partition, mount those partitions as well. For example, if you want to have a different partition for /home or /var, then do:

 $ mkdir /mnt/var
 $ mount /dev/sd?? /mnt/var
 $ swapon /dev/sd??

Note: UEFI

If installing a UEFI system make sure to select the efibootmgr and grub2-efi packages from the opt collection during the package selection phase.

After the packages have finished installing, the setup script will display an installation log. Make sure the last line in the log says “0 error(s)”.

If you missed/forgot to install certain packages, you can just mount the CRUX installation media and use pkgadd to install them.

Screenshots of setup

Note

There is a shortcut command for creating the chroot environment: setup-chroot. This will execute all these steps at once.
 $ mount --bind /dev /mnt/dev
 $ mount --bind /tmp /mnt/tmp
 $ mount -t proc proc /mnt/proc
 $ mount -t sysfs none /mnt/sys
 $ chroot /mnt /bin/bash
 $ passwd

Note

Make sure to include drivers needed to bring up your root filesystem! Such as "SCSI disk support", filesystem and disk controller. For example:

Note

The setup program installs a configuration file /usr/src/linux-4.9.x/.config which is a good starting point for a custom kernel, because all needed options, like CONFIG_DEVTMPFS, are enabled.
 $ cd /usr/src/linux-4.9.x
 $ make menuconfig
 $ make all
 $ make modules_install
 $ cp arch/x86/boot/bzImage /boot/vmlinuz
 $ cp System.map /boot

Upgrading From CD-ROM or removable flash drive

 $ md5sum crux-3.3.iso

Compare the output with the file crux-3.3.md5, which can be found in the same directory as the ISO image on the download site. If the checksums match, the download was successful and you can continue by burning the ISO image to a CD or writing it to a removable flash drive.

 $ mount /dev/sd?? /mnt

If your installation spans over more than one partition, mount these partitions as well. For example, if you have a different partition for /var, then do:

 $ mount /dev/sd?? /mnt/var
 $ swapon /dev/sd??

Note

The setup script uses the /etc/pkgadd.conf of the target system to determine which files to upgrade, and which files to not upgrade. The files that are not upgraded are put in /var/lib/pkg/rejected/ (Section "Upgrading a Package").

When the setup script has upgraded the selected packages an upgrade log will be displayed. Make sure the last line in the log says “0 error(s)”. If you missed/forgot to install certain packages, you can just mount the CRUX installation media and use pkgadd to install them (e.g. pkgadd /mnt/crux/opt/package#1.0-1.pkg.tar.gz).

Note

There is a shortcut command for creating the chroot environment: setup-chroot. This will execute all these steps at once.
 $ mount --bind /dev /mnt/dev
 $ mount --bind /tmp /mnt/tmp
 $ mount -t proc proc /mnt/proc
 $ mount -t sysfs none /mnt/sys
 $ chroot /mnt /bin/bash
udev reads files in /sys/* and /proc/*. Make sure that those pseudo filesystems are enabled in your kernel configuration and available during system-startup. Also note that udev doesn't automatically mount /dev/pts. Terminal applications such as xterm(1) will not work if you forget to mount it. We highly recommend you check your fstab file:''
# <dev> <dir>         <type> <options> <dump> <pass>
[..]
devpts  /dev/pts      devpts noexec,nosuid,gid=tty,mode=0620  0      0